勘误表 (1)
-
Errata sheet LPC18S5x, LPC18S3x, flash-based devices[ES_LPC18S5X_S3X_FLASH]
紧凑列表
32-Bit Arm® Cortex®-M3 MCU; 1 MB Flash and 136 KB SRAM; Ethernet, Two High-Speed USB, EMC, AES Engine
The LPC18S37JBD144 is a Arm Cortex-M3 based microcontroller for embedded applications. The Arm Cortex-M3 is a next generation core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration.
The LPC18S37JBD144 operates at CPU frequencies of up to 180 MHz. The Arm Cortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals. The Arm Cortex-M3 CPU also includes an internal prefetch unit that supports speculative branching.
The LPC18S37JBD144 includes 1 MB of flash and 136 kB of on-chip SRAM, 16 kB of EEPROM memory, a quad SPI Flash Interface (SPIFI), a State-configurable Timer/PWM (SCTimer/PWM) subsystem, two High-speed USB controllers, Ethernet, an external memory controller, and multiple digital and analog peripherals.
sot486-1_3d
产品详情
Features
-
Processor core
- Arm Cortex-M3 processor (version r2p1), running at CPU frequencies of up to 180 MHz.
- Arm Cortex-M3 built-in Memory Protection Unit (MPU) supporting eight regions.
- Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC).
- Non-maskable Interrupt (NMI) input.
- JTAG and Serial Wire Debug, serial trace, eight breakpoints, and four watch points.
- Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support.
- System tick timer.
-
On-chip memory
- 1 MB on-chip dual bank flash memory with flash accelerator.
- 16 kB on-chip EEPROM data memory.
- 136 kB SRAM for code and data use.
- Multiple SRAM blocks with separate bus access.
- 64 kB ROM containing boot code and on-chip software drivers.
- 64 bit+ 256 bit of One-Time Programmable (OTP) memory for general-purpose use.
- AES engine for encryption and decryption of the boot image and data with DMA support and programmable via a ROM-based API.
-
Clock generation unit
- Crystal oscillator with an operating range of 1 MHz to 25 MHz.
- 12 MHz internal RC oscillator trimmed to 3 % accuracy over temperature and voltage (1.5 % accuracy for Tamb = 0 °C to 85 °C).
- Ultra-low power RTC crystal oscillator.
- Three PLLs allow CPU operation up to the maximum CPU rate without the need for a high-frequency crystal. The second PLL can be used with the High-speed USB, the third PLL can be used as audio PLL.
- Clock output.
-
Configurable digital peripherals:
- State Configurable Timer/PWM (SCTimer/PWM) subsystem on AHB.
- Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and outputs to event driven peripherals like timers, SCTimer/PWM, and ADC0/1.
-
Serial interfaces
- Quad SPI Flash Interface (SPIFI) with 1-, 2-, or 4-bit data at rates of up to 52 MB per second.
- 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time stamping (IEEE 1588-2008 v2).
- One High-speed USB 2.0 Host/Device/OTG interface with DMA support and on-chip high-speed PHY (USB0).
- One High-speed USB 2.0 Host/Device interface with DMA support, on-chip full-speed PHY and ULPI interface to an external high-speed PHY (USB1).
- USB interface electrical test software included in ROM USB stack.
- Four 550 UARTs with DMA support: one UART with full modem interface; one UART with IrDA interface; three USARTs support UART synchronous mode and a smart card interface conforming to ISO7816 specification.
- Up to two C_CAN 2.0B controllers with one channel each.
- Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA support.
- One Fast-mode Plus I²C-bus interface with monitor mode and with open-drain I/O pins conforming to the full I²C-bus specification. Supports data rates of up to 1 Mbit/s.
- One standard I²C-bus interface with monitor mode and standard I/O pins.
- Two I²S interfaces with DMA support, each with one input and one output.
-
Digital peripherals
- External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash, and SDRAM devices.
- SD/MMC card interface.
- Eight-channel General-Purpose DMA controller can access all memories on the AHB and all DMA-capable AHB followers
- Up to 83 General-Purpose Input/Output (GPIO) pins with configurable pull-up/pull-down resistors.
- GPIO registers are located on the AHB for fast access. GPIO ports have DMA support.
- Up to eight GPIO pins can be selected from all GPIO pins as edge and level sensitive interrupt sources.
- Two GPIO group interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins.
- Four general-purpose timer/counters with capture and match capabilities.
- One motor control PWM for three-phase motor control.
- Repetitive Interrupt timer (RI timer).
- Windowed watchdog timer.
- Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytes of battery powered backup registers.
- Event recorder with three inputs to record event identification and event time; can be battery powered.
- Alarm timer; can be battery powered.
-
Analog peripherals
- One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s.
- Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s. Up to eight analog channels total. Each analog input is connected to both ADCs.
- Unique ID for each device.
-
Power
- Single 3.3 V (2.4 V to 3.6 V) power supply with on-chip internal voltage regulator for the core supply and the RTC power domain.
- RTC power domain can be powered separately by a 3 V battery supply.
- Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down.
- Processor wake-up from Sleep mode via wake-up interrupts from various peripherals.
- Wake-up from Deep-sleep, Power-down, and Deep power-down modes via external interrupts and interrupts generated by battery powered blocks in the RTC power domain.
- Brownout detect with four separate thresholds for interrupt and forced reset.
- Power-On Reset (POR).
- Available in a LQFP144 package
Target Applications
- Secure industrial gateways
- Automotive aftermarket, including telematics
- Smart meters
- Industrial controls
- Industrial automation
- Diagnostic equipment
- White goods HMI
- Data collectors and navigation
- Electronic instruments
购买/参数
1 结果
包含 0 不推荐用于新设计
部件 | 订购 | 计算机辅助设计模型 | 运行频率[最高]（MHz） | Flash (kB) | EEPROM (kB) | GPIO | 以太网 | USB Controllers | USB (speed) | USB (type) | CAN | UART | I2C | SPI | ADC通道 | ADC位数 | ADC | 定时器 | Timer (bits) | SCTimer / PWM | 封装类型 | 温度范围 | 电源电压[最小]（V） | 电源电压[最大]（V） | 状态 | 产品类别 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
180 | 1024 | 16 | 83 | 1 | 2 | HS (2x) | host/device | 2 | 4 | 2 | 3 | 2 | 10 | 400 ksps | 10 | 32 | 1 | LQFP144 | -40 °C to +105 °C | 2.4 | 3.6 | 正常供应 | 140-LPC1800- |
1-10 / 13 文件
紧凑列表
勘误表 (1)
-
Errata sheet LPC18S5x, LPC18S3x, flash-based devices[ES_LPC18S5X_S3X_FLASH]
培训资料 (1)
封装信息 (1)
应用笔记 (7)
数据手册 (1)
用户指南 (1)
简介 (1)
-
LPC18Sxx Series of MCUs - Fact Sheet[LPC18SXXLF]
设计资源
硬件
快速参考恩智浦
板类型.
1-5 / 7 硬件
-
仿真器、探测器、编程器Universal Multilink开发接口
正常供应 -
仿真器、探测器、编程器PEmicro Cyclone编程器
正常供应 -
仿真器、探测器、编程器PEmicro Cyclone FX编程器
-
其他可用硬件. 查看我们的精选合作伙伴解决方案.
-
仿真器、探测器、编程器MCU-Link Pro硬件调试器
正常供应 -
仿真器、探测器、编程器Universal Multilink FX高速开发接口
正常供应
软件
快速参考恩智浦 软件类型.
1-5 / 6 软件文件
-
开发IDE和生成工具
MCUXpresso集成开发环境（IDE）亮点
-
BSP及设备驱动
LPC SPIFI外设
-
连接软件
LPC1850 USB Certification Support Pack
-
可访问其他软件。 查看我们的精选合作伙伴解决方案.
-
样品及快速入门软件
MCUXpresso软件开发套件(SDK)
注意: 推荐在电脑端下载软件，体验更佳。
工程服务
支持
您需要什么帮助?
近期查看的产品
LPC43S70FET256
32-Bit Arm® Cortex®-M4 + 2 X M0 MCU; 282 KB SRAM; Ethernet; Two HS USBs; 80 Msps 12-Bit ADC; Configurable Peripherals, AES Engine
购买选项